Image generated with AI
Blender tree: trunk, branches and leaves with Geometry Nodes
Diego Cortés
Author
A tree in Blender gives itself away the moment you copy it: same trunk, same leaves, same silhouette. With a curve for the trunk and Geometry Nodes for the branches and leaves, every copy comes out different without modelling anything new.
Nothing here is sculpted or simulated. The tree gets assembled from parts: the trunk is a curve with a profile, the branch is one piece that repeats, and the leaves are instanced cards, not geometry.
Why build a procedural tree in Blender (and not download one)
A downloaded model solves one tree; a system solves the landscape. With a purchased asset you end up rotating and mirroring the same mesh until the eye catches the repetition. With Geometry Nodes you change the seed and get another plant, with different branches and a different leaf spread.
The second advantage is weight: the leaves are not geometry, they are flat cards with a texture and an alpha channel repeated through instances, so hundreds of leaves cost what one costs. The third is that the tree stays editable through parameters: ask for a taller tree and nothing gets remodelled, a value gets adjusted. If you never touched these nodes, start with Geometry Nodes from scratch.
The trunk: how a tree in Blender starts from a single curve
Draw the base curve
Add a Bezier curve or a Path with few control points. The trunk bends where a point sits, not where you push it: three or four well placed points describe a believable tree. Think of the curve as the axis of the trunk, not as its surface; there is no surface yet.
Bevel turns the line into a trunk
In the curve properties, Geometry panel, enable Bevel and pick Round. Depth is the size of the cross section, meaning the thickness, and Resolution is how many vertices that section gets: low gives a faceted tube, high a smooth surface. Fill Caps seals the tube. Without Bevel the curve stays a chain of edges.
Taper so it is not a pipe
The Taper Object is a second 2D curve assigned to the first: its X axis is the position along the trunk and its Y the scale. Where that curve drops, the trunk narrows, and not a single control point is added to the axis. The manual warns the name is misleading, since it can scale any size at any point, not just the radius. Once the volume is there, bark belongs to procedural materials.
Branches: one branch, many branches with Instance on Points
Points along the trunk
Resample Curve spreads points along the trunk: Count fixes how many per spline and Length creates segments of a given size, rounding down so a whole number fits. Spline Parameter decides where each point lands: Factor gives the portion of total length and Length the distance travelled, which lets you cluster branches up high and keep the lower trunk clean.
Instance the branch
Model a single branch, a short curve with its own Bevel, and feed it into Instance on Points. The position of the input points drives the transform of each instance, and Rotation and Scale apply per point. If the input geometry already carries instances, you get nested instancing.
Variation with Random Value
Without variation every branch leaves at the same angle and the tree looks like a comb. Random Value has Min, Max, Probability, ID and Seed; Vector suits rotation and Decimal suits scale. The Seed makes the result reproducible: change the number and another tree appears, put it back and the previous one returns.
Joints that do not cut
Fillet Curve rounds the corners with an arc Radius, and Limit Radius stops two fillets from overlapping. Then Curve to Mesh turns the set into a surface: with a Profile Curve the section is extruded along every spline, Scale adjusts the profile at each control point and Fill Caps fills the end when the profile is cyclic. Without a profile you only get a chain of edges.
Leaves: instanced cards, not real geometry
Where the leaves go
The tool is Distribute Points on Faces and it needs a mesh with faces, so the branches must have passed through Curve to Mesh. Set Density Max in points per square metre and a seed. Random is the fastest method; Poisson Disk respects a Minimum Distance, which is what keeps leaves from piling up.
The card and its material
A small plane with a leaf texture and alpha. In the material, enable Backface Culling for Camera: the manual recommends it whenever possible because it saves render work, and nothing is lost here. If you use a Transparent BSDF, decide what to do with Transparent Shadows, and under Render Method pick Dithered, which works well with passes and ray tracing. Card UVs are covered in UV mapping in Blender.
Clean edges
With Dithered and ray tracing the edge comes out noisy, and the manual solves it by quantising alpha to 0 or 1: a Math node in Greater Than mode before the texture is connected. The pixel is opaque or invisible, with no in between greys, and the edge stops shimmering.
Stop it looking cloned
A plane repeated a thousand times gives itself away when every leaf points the same way. Two fixes: a Random Value driving scale and rotation per leaf, and Rotate Instances, which works with Instances, Selection, Rotation, Pivot and Local Space to orient by groups.
Wind without simulation
Wave modifier
The short route is deformation. The Wave Modifier displaces along Z from an origin point, with circular fronts when X and Y are active. Height is the amplitude and Width half the distance between crests; Cyclic repeats the cycle and Damping fades the motion towards the base. With a Vertex Group you move only the crown and leave the trunk still, which is what makes it believable.
With Geometry Nodes
Scene Time outputs Seconds and Frames, accepts non-integer values and drives a variation applied with Rotate Instances or with Set Position, where motion goes in through Offset (the default Position equals the Position node and does nothing). The tree sways the same way, but the motion lives in the nodes. There is a dedicated video: how to add wind effects on trees in Blender.
From one tree to a forest: instances, not copies
Terrain and scattering
The same distribution node works on the ground, with Density Max and, above all, Poisson Disk and a Minimum Distance so the trees do not overlap. If the terrain has steep slopes, filter by the normal before instancing or you get trees growing sideways.
Instance the whole tree
The tree is instanced, not copied, and that difference is pure performance: most nodes process each unique geometry only once instead of every instance. Realize Instances materialises the mesh when you need to edit it, and then you lose that advantage. There is more in heavy scenes and render memory. Two or three base trees with a Random Value on scale and rotation keep the forest from repeating; the next step, scattering ready-made assets over a terrain, is in scattering with Geometry Nodes.
The mistakes that make a tree look fake
The perfectly spherical canopy is the most common one. Then uniform leaf size, and the cylindrical trunk without taper. Visible repetition gives away a single seed across the whole forest. And the last one belongs to the shot, not the tree: a hard shadow with no ambient light flattens everything, so read why 3D renders look fake and sort the sky with Sky Texture or an HDRI from exterior lighting.
Conclusion
A tree built this way is not a model, it is a system: changing the bevel depth thickens the trunk, changing the seed gives another plant, changing the density fills the crown with leaves. That is the difference between owning one tree and owning a forest in a file that opens in seconds.
To watch it happen, the platform keeps the curated tutorials for this: Ryan King Art's pine tree branch (pine tree branch), the stylised trees with snow (stylized trees with snow), the procedural bark (procedural tree bark) and CG Boost's large-scale forests (scatter large-scale forests). Technical sources: the Blender 5.2 LTS manual, curve properties and geometry nodes.